An extension
Slide an extension against the house, choose the size and the roof, and see straight away the floor, volume, new facade and the roof, and whether it fits on the plot.
Building on your home
Search for an address and your home appears in 3D, with the neighbours and the plot. Add an extension or a dormer, raise a roof, remove a shed or place your own design. You see straight away how much floor, volume, facade and roof you add, and whether it fits on the plot.
0m³ volume
0m² on the ground
0m² roof
0m² facade
Model of the house
Turn with your finger or mouse. Tap a roof face or facade to change it. Drag what you add; an extension snaps to the facade close to the house, a dormer stays on the roof. The ring rotates it, the corners make it bigger or smaller, the ball makes it higher or lower (Shift: bigger steps).
Tap a roof face to make it lower or higher. This applies to this design.
Tap a facade to move it, or to stop counting it as a facade.
Nothing yet. Add an extension, put a dormer on the roof, or import your own design as a 3D model (GLB from SketchUp, Revit, ArchiCAD or Blender).
Nothing. With Remove building you tap a building, of the house or of the neighbours, and then it is gone in this design.
More than one project?
For free you can save one project. With the Business subscription you save unlimited projects, for example for your clients.
Slide an extension against the house, choose the size and the roof, and see straight away the floor, volume, new facade and the roof, and whether it fits on the plot.
Put a dormer on a sloping roof, make it wider or taller, and see the volume and facade you add.
Make a roof face higher or lower, or slide a facade out or in. The volume, the roof and the facades update straight away.
Remove a shed, an old extension or the whole house, and put something new there. Your own design too: import it as a 3D model (GLB) and put it in place.
Try several designs in one project, for example an extension 3 versus 4 metres deep, and put them side by side with Compare.
The shape comes from the AHN height measurements, with the outline from the BAG: the volume above ground, the ground area, the facades and each roof face with its real area, pitch and direction.
The plot boundary from the Kadaster. If your house shares a roof with the neighbours, we only count the part above your own plot.
Lay the aerial photo over the plot and the roofs, and see whether the model matches what is really there.
It is a good estimate, not a survey. The shape comes from measurements from the air: a few points per square metre. Small things like a chimney, gutter or overhang sometimes do not show. For a quote, specification or permit, check the measurements on site.
Everything above ground level, from the ground to the roof, including the attic. Not a cellar or crawl space, and an overhang only between its underside and the roof. That is close to the gross volume, but it is not a measurement according to NEN 2580.
From the BAG, as the municipality registered it. That is measured inside the walls, so it differs from the ground area here, which is measured from the outside.
The height of the lowest edge of the main roof above ground level, where the gutter usually is. The highest point is the ridge, or on a flat roof the roof edge. A canopy or bay window does not count.
Our map calculates the roofs itself from the AHN point cloud, with what we add to it: overhangs, chimneys and roof faces that continue. The 3D BAG from TU Delft and 3DGI is the well-known model without those additions. Choose per design which model you use and put them side by side with Compare.
In The house, tap a roof face and make it lower or higher, or give it a different pitch. You slide a facade out or in; the roof behind it moves along. If a piece of wall is not really a facade, untick Counts as facade. This only applies to the design on screen, and As measured puts it back.
bouwendoor.nl does not tell you that: it depends on the zoning plan, the position on the property and the national rules. Check it with the Vergunningcheck (permit check) on the Omgevingsloket. The measurements here do help you fill it in.
Save a project per client with its own name and a note, and share the link, so your client can view the designs in 3D themselves. Add more designs and put them side by side with Compare. With Copy measurements you paste everything into a spreadsheet or quote, and with Print you get it on paper or as a PDF. Everything is free with one project; with the Business subscription you save unlimited projects.
On rijdendoor.nl you can measure a length, perimeter, area or height in 3D yourself, with Measure in the menu or on the card of a building.
From open data: the AHN height measurements, the buildings and addresses of the BAG, the plots of the Kadaster, the 3D BAG and the aerial photo from Beeldmateriaal Nederland. All sources are on doornl.nl/bronnen.